How to replace cone crusher wall
Linkedin

How to replace cone crusher wall

Zhengzhou : China | May 05, 2012 at 8:14 PM PDT
XX XX
Views: Pending
 
How to replace cone crusher wall

Cone crusher wall is mainly fixed in the cone body with conical head, and cast zinc alloy between the two. After first installation or replacement cone crusher wall for 6-8 hours, you should check the fastening, if find loose, should immediately fasten it.

Crusher and its equipment:

Output production of the crusher: the feed to the feed block, the block size of the row of ore, ore physical mechanical properties, temperature and other relevant variables, so the manufacturer for a given output is in terms of their designation under the approximate throughput. Production of aggregates by the equipment include the following: cone crusher, jaw crusher, impact crusher, impact crusher, and a matching circular Sand and Gravel equipment.

The cone crusher is of big crushing ratio, high efficiency, low energy consumption, uniform particle size and suitable for crushing hard ore, etc., and thus widely favored by the mineral processing sector. Cone crusher liner often has a strong impact, prone to severe wear. This causes non-uniform particle size, the decline in production efficiency and energy consumption increases, so the crusher liner replacement is essential. Replacement of the new liner is usually used in high temperature zinc alloy casting or at room temperature high-grade cements mortar casting method, often broken wall with loose rolling ace tabular wall, fixed difficulty, seriously affecting the production of normal operation in the production and maintenance processes. Based on past experience shows, the replacement of a cone crusher liner and casting time required is approximately 7 to 10 days, the replacement cycle is too long, seriously affecting the normal production schedule, for the relevant staff continue to explore and study, repeated practice is accumulated, the development of a cone crusher liner to fill the new technology - epoxy filler (broken rear rubber lined).

nicole006py is based in Beijing, Beijing, China, and is a Reporter for Allvoices.
Report Credibility
 
  • Clear
  • Share:
  • Share
  • Clear
  • Clear
  • Clear
  • Clear
 
 
 
Advertisement
 

Blogs

 >
  • How to replace cone crusher wall nicole007py

      nicole007py.bcz.com
    After first installation or replacement cone crusher wall for 6-8 hours, you should check the fastening, if find loose, should immediately fasten it. Crusher and its ... Cone crusher liner often has a strong impact, prone to severe wear. This causes .
  • 6 points for cone crusher maintenance attention

      cone-crusher.ezinemark.com
    Cone crusher wall with conical head fixed in the cone on the body between the two casting zinc alloy, broken wall after 6-8 hours, should check the fastening of a new installation or replacement of the cone, found loose shall be immediately ... Due
  • 6 points for cone crusher maintenance attention - cathyma's blog

      cathyma.hatenablog.com
    Cone crusher wall with conical head fixed in the cone on the body between the two casting zinc alloy, broken wall after 6-8 hours, should check the fastening of a new installation or replacement of the cone, found loose shall be immediately ...
  • Cone crusher

      quarrycrusher.blox.pl
    crusher Cone Crushers are fabricated with highest quality of material and workmanship, with the state of art in design. crusher Cone Crushers are designed for efficient application of crushing in mining industry, for efficient down sizing of various
  • quarrycrusher » Cone crusher

      quarrycrusher.podbean.com
    crusher Cone Crushers are fabricated with highest quality of material and workmanship, with the state of art in design. crusher Cone Crushers are designed for efficient application of crushing in mining industry, for efficient down sizing of various
  • How to Replace Fragile Parts of Sand Maker

      www.briefingwire.com
    Sand the board hammer: counter broken boards hammer wear to a certain extent should be timely adjustment or change in order to avoid the damage of fasteners and other components. Sand liner: Open shelters, demolition of a fixed fight back liner

More From Allvoices

Report Your News Got a similar story?
Add it to the network!

Or add related content to this report



Use of this site is governed by our Terms of Use Agreement and Privacy Policy.

© Allvoices, Inc. 2008-2014. All rights reserved. Powered by PulsePoint.